|
|
    
|
Micro Accessories
Micro Test Blocks-These blocks are used to check the accuracy of your Micro Hardness Tester, available for the Knoop or Vickers hardness tests. Calibrated at our standardizing laboratory, micro test blocks are available in a wide range of hardness values and can be calibrated at any of the standard loads.
Knoop and Vickers Indenter-Both indenters are diamond ground. The Vickers is in the form of a square based pyramid with an angle of 136o between faces. The Knoop is in the form with a diagonal line length of 7.11:1. The Knoop test allows continuous indentations to thinner specimens at closer intervals. We carry replacement indenters for most Micro hardness testers.
Rockwell Accessories
Brinell Accessories
There are many different items that we carry in stock. So many that it is difficult to list them all. We carry Floor Stands for bench type testers, we carry printers to print out your testing results and we also carry Jominy fixtures to use for the end quench test. This is just a brief list of some of the different types of equipment we carry for hardness testing. Contact us with any questions or specifics on what you need and we can assist you. |
Self
Leveling Vise-This accessory can be used to
hold tapered pieces, wire, mounted samples, etc. The measuring plane is at
a horizontal level and causes an extremely efficient measuring operation.
Horizontal
Fine Specimen Measuring Device-This accessory
is used for testing unmounted rounds from 0.5 ~ 4mm.
Clamping
Device-Standard vise used for securing a wide
range of specimens for easy and accurate testing.
Larger
Steel Test blocks-This item is new to our
line. The size of this steel test block is 2 1/2" X 3/8".
They are made of hardened steel and are offered in many scales and ranges.
Used for determining the accuracy of your hardness tester. 
Steel
and Brass test blocks-Of brass or hardened
steel. Used for determining the accuracy of your hardness tester.
Test
block calibration set-Provide complete
control not only in the accuracy of the tester checked, but also in the accuracy
and condition of the penetrators.
Diamond
Penetrators- Used for testing hardened
steels. Available in "C", "N", "A" and
"C&N" scales. We offer special types of indenters to fill
your needs. 
Penetrator
Extensions-Used to check deep internal
surfaces. Available in 1", 2", 3", 4" and 5" lengths.
Steel
Ball penetrators-Used for testing unhardened
steels. Available in sizes of 1/16", 1/8", 1/4" and
1/2" diameter. We also offer replacement balls for all sizes.
Anvils-We
carry a large line of anvils. Available in many different sizes so it
makes it easier on you to test your material. We carry eyeball anvils
for testing tapered parts. We carry 3 1/2" Vee anvils for testing
large, round and cylindrical parts. As you can see there is a wide variety
shown
here. We are able to make up any type of anvil for your special
requirements. Just call, we most likely already have it in stock.
8"
Flat Table Anvil-For supporting large pieces
during testing. Fitted on the elevating screw.
Gooseneck
Adapter-Used for checking inside diameter of
tubes and rings.
Extension
Rest-Used for supporting long pieces during
testing.
Jack
Rest-Used to support tubes, bars and other
extra long or heavy pieces.
Brinell
Microscopes and Stage Micrometers-This highly
efficient instrument can be used under normal room lighting conditions.
With the added feature of the micrometer measuring eyepiece, highly accurate
readings are obtained. It comes ready to use with a handy case for safe,
convenient carrying. The stage micrometer is used for making sure the
Microscopes are calibrated properly.
Brinell
Test Block-The Brinell test blocks are
available in the 500 kg to 3000 kg loads. We offer them in
hardened steel and aluminum when the load is applicable.
Brinell
Ball penetrators-We have many different style
of penetrators available. We have stock for many varieties of makes of
Brinell hardness testers. We also carry Steel and Carbide balls for the
penetrators.